ServicesGutter Repair
Gutter Repair in North Charleston
We fix the gutters you already have: leaking seams, sagging runs, pulled hangers and sections that hold standing water. You get a clear diagnosis, a written scope and an arrival window you can plan your day around.

When repair is the right call
Most gutter problems start small. A bead of sealant at a corner miter dries out and cracks, a hanger screw backs out of soft fascia, or one run loses its slope and starts to pond. Left alone, that water finds the fascia board, the soffit or the soil against your foundation.
Repair makes sense when the gutter body is sound and the trouble is local: joints, end caps, fasteners, pitch or a short damaged length. If the metal is thin, rusted through in several places or the profile is too small for your roof, we will say so and explain why gutter installation would cost you less over time. You get that answer before any work is scheduled.
Our scheduling is built around realistic timelines. We give you an arrival window, not a vague day, and if weather or a longer job ahead of yours shifts the plan, we call you before the window opens.
What a gutter repair visit covers
Joint and end cap resealing
We cut out old, failed sealant, clean the metal to bare surface and apply fresh gutter sealant rated for exterior metal. Corner miters and end caps get the same treatment, since they flex the most.
Hanger replacement and rehanging
Old spike-and-ferrule fasteners loosen as wood expands and shrinks. We replace them with hidden hangers screwed into solid fascia, spaced closer where the run carries heavy roof runoff.
Pitch correction
Gutters need a slight fall toward the outlet, roughly a quarter inch every ten feet. We check the slope with a level and reset hangers so water stops pooling mid-run, where it breeds rust and mosquitoes.
Section patching or replacement
A dent from a ladder or a fallen limb can trap water. Small holes get a matching metal patch; a crushed or split length gets replaced with a section matched to your existing profile as closely as possible.
Fascia check behind the gutter
We probe the board where hangers attach. If the wood is soft, we show you photos and explain your options before fastening anything to it.
Signs your gutters need repair
Drips at corners and seams
When water falls from a joint rather than the outlet, the sealant there has let go. A dark streak on the siding beneath is a common giveaway.
A gap opening at the roofline
If the back edge of the gutter has pulled away from the fascia, the hangers have loosened or the wood holding them is failing. Runoff then slips down the fascia board and never reaches the trough.
Water still sitting a day later
A section that holds a puddle long after a storm has lost its slope. That constant wetness wears down aluminum and steel well before their time.
Overflow in heavy rain
A little spill at roof valleys during a hard summer thunderstorm is normal. A steady sheet pouring over the front lip usually means a sag or a clogged outlet transition.
Peeling paint or rot on fascia
Bubbling paint or wood that feels spongy right behind the gutter tends to mark a slow leak that has been working on the board for months.
How a repair job runs
- 1
Phone call and arrival window
You describe what you are seeing and we set a free estimate visit with a specific arrival window. If anything changes on our end, you hear from us before that window, not after it.
- 2
Inspection and written scope
We walk the full gutter line, not just the spot you noticed, and photograph joints, hangers and fascia. You get a written scope listing each repair so you can see exactly what you are paying for.
- 3
Scheduled repair day
Most residential repairs are finished in one visit. We set ladders with standoffs to protect the gutter edge, keep materials off your plantings and tell you roughly how long we expect to be there.
- 4
Water test and walkthrough
When the work is done we run water through repaired sections to confirm the seams hold and the slope drains. Then we walk you through what we changed and haul away old hangers and scrap.
What moves the price of a gutter repair
We price a repair only after we have been up the ladder and seen the joints, hangers and fascia for ourselves. The written scope breaks out each item on its own line. If something new turns up mid-job, we talk with you before it is added.
- How many spots have failed
- Two cracked corner miters take a short visit. A sectional system leaking at twenty joints along the eaves is a much longer one.
- The wood behind the gutter
- Hangers only hold in sound fascia. If the board is rotted, it has to be dealt with before the gutter goes back up, and the scope grows to match.
- Eave height and access
- Second-story eaves, steep roof pitches and narrow side yards add setup time and can call for extra ladders or standoffs.
- Matching your existing profile
- An older aluminum K-style run or a half-round system can be harder to match, which affects parts cost when a section needs replacing.
Gutter repair questions
Something not covered here? (843) 612-5300
My gutters are getting old. Should I fix them or start over?
When the metal body is still sound and the trouble sits at joints, hangers or slope, a repair usually gives you more for your money. Rust-through in several places, or a profile too small for the roof area it drains, tips the balance toward gutter installation. Either way, you see our photos and hear a straight recommendation before anything is scheduled.
How long does a typical repair take?
A single-story repair is usually a few hours. Resetting the pitch along several runs or working around soft fascia can stretch to most of a day. We give you an expected duration when we book the visit so your day is not left open-ended.
Do I need to be home during the repair?
No, the work happens outside. We do need access to every side of your home, including any locked gates. We call when we arrive and again when we wrap up to walk through what we did.
Why does the same corner keep leaking?
A corner miter absorbs the most movement from heat, cold and the weight of runoff, so its sealant gives out first. Many repeat leaks also trace back to a miter that was cut or fastened poorly to begin with. We strip the old sealant completely and check how the joint fits before resealing, instead of smearing a new layer over the old one.
What if it rains on my scheduled day?
Gutter sealant will not bond to wet metal, so we do not seal joints in active rain. If the forecast changes, we call you before your arrival window with the next open slot rather than leaving you waiting.

Get leaking gutters fixed on a schedule you know
Tell us what you are seeing and we will set an inspection with a clear arrival window. You get a written scope before any repair work begins.